العودة إلى المدونة
أدلة إرشادية 2026-11-21 PRL Motorsports - Premium Automotive Performance Products 0 مشاهدة

How to Install Genuine Honda Side Welcome Lights

How to Install Genuine Honda Side Welcome Lights

Step-by-step guide to installing Genuine Honda Exterior Side Welcome Lights on compatible Ridgeline, Pilot, and Passport models.

What the Genuine Honda Side Welcome Lights Do

  • Genuine Honda Exterior Side Welcome Lights 08V27-TG7-100: Side Welcome Light illuminates when your vehicle is unlocked with key fob or door is opened to provide a luxurious, upscale appearance. This automatic on/off behavior means no manual switch needed — the lights turn on when you approach or exit, adding convenience and a premium feel.
    Genuine Honda Exterior Side Welcome Lights 08V27-TG7-100
    Genuine Honda Exterior Side Welcome Lights 08V27-TG7-100
  • Genuine Honda Exterior Side Welcome Lights 08V27-TG7-100: Fits all 2017+ Honda Ridgeline, all 2018+ Honda Pilot, all 2019+ Honda Passport, and all variant models including RHD and International Models. Compatibility is broad across these three SUV/truck platforms, but you must confirm your exact model year and side before ordering.

Before You Begin: What the Kit Includes

The Genuine Honda Exterior Side Welcome Lights (part number 08V27-TG7-100) are a factory Honda accessory. The kit replaces the existing lower side trim panels with pre-wired light assemblies that connect to your vehicle’s door and key fob unlock signal. Because this is a genuine Honda part, no cutting or splicing of factory wiring is required — it plugs into existing connectors behind the trim.

You will need basic hand tools: a trim removal tool or flathead screwdriver (wrapped in tape to avoid scratching paint), a T20 or T25 Torx driver (depending on your model), and a small flashlight to locate the wiring harness behind the trim. No power tools are necessary.

Step-by-Step Installation

  1. 1. Park and Prepare: Park your Honda on a level surface. Turn off the engine and open the door you plan to work on first. Have the side welcome light kit and tools within reach.
  2. 2. Remove the Lower Side Trim Panel: Locate the lower side trim panel below the door opening on the exterior of the vehicle. Using a trim removal tool, gently pry the panel away from the body starting at the rear edge. Work forward, releasing the plastic clips. Set the original panel aside — it is not reused.
  3. 3. Locate the Factory Wiring Connector: Behind the trim panel you will find a pre-wired connector (usually taped to the body or tucked into a pocket). This is the same connector used for the factory welcome light option. Pull it out gently so you can reach it.
  4. 4. Connect the Welcome Light Assembly: Take the new side welcome light from the kit and plug its connector into the factory harness. The connectors are keyed to fit only one way — do not force them. Once connected, tuck the wiring back into the body cavity so it does not pinch when the trim is reinstalled.
  5. 5. Install the New Trim Panel: Align the new welcome light trim panel over the mounting clips. Press firmly along the edges until all clips snap into place. Verify that the panel sits flush with the surrounding body panels.
  6. 6. Repeat for the Opposite Side: Install the second side welcome light following the same process on the other door. Both sides are identical in procedure.
  7. 7. Test the Lights: Lock and then unlock your vehicle with the key fob. The side welcome lights should illuminate as the doors unlock. Also test by opening each door — the light on that side should turn on. If a light does not work, double-check the connector is fully seated.

What the Catalog Does Not Confirm

The supplied information does not include specific torque values for the trim clips, wiring routing diagrams, or detailed connector locations for every model variant. Because the light assembly uses factory connectors, installation is straightforward, but if you encounter resistance or an unfamiliar harness, consult your vehicle’s service manual or a Honda dealership for model-specific wiring details. The kit is designed for the models listed, but individual vehicle configurations (such as aftermarket side steps or running boards) may affect fit.

مقالات ذات صلة

Customer Service
الرئيسية
المنتجات
السلة
الملف الشخصي